Lighting remains an essential element in decorating a home. You have the choice between different models of lighting fixtures such as ceiling lights, spotlights or wall lights.
Diffusing a soft light, wall lights are perfect for providing subtle lighting. In fact, the design possibilities for a wall light are virtually unlimited.
Materials needed to make a wall light
Making a wall light remains an easy and quick solution to have an elegant and inexpensive light fixture . It is a task within the reach of any good DIYer.
Among the essentials, you will find a wooden bracket, a 3*15 mm² electric cable, a suspension socket and a suspension. All these essential elements and tools are easily found in DIY stores .
Once the materials are gathered, prepare the wooden bracket . To do this, mark 3 points on the bracket with a pencil. The first on the upright to be fixed to the wall and the other two on the upper upright. Using an electric drill, drill the bracket by making holes of a sufficient diameter so that the electric wire can pass through.
Installing the electrical wire
The next step is to install the electrical wire and connection. To do this, install an electrical wire by passing it through the holes drilled in the bracket.
Remember to leave a length of wire on the front to adjust the height of the suspension. Then, temporarily position the homemade wall light in the intended location and test to find the ideal height . Then, cut the wire using pliers and strip it to connect it to the socket.
It may be necessary to adjust the length of the low wire by cutting it if necessary. Before installing the wall light on the wall, you must first turn off the power supply at the circuit breaker .
If there is no electrical connection point on the wall, you must create one. You must strip the lower end of the wire before connecting it to the electrical circuit in the wall.
Connecting and fixing the wall light to the wall
There are two ways to connect a wall light to the wall depending on whether or not it has a DCL. For a model without a DCL box , you must start by identifying the three power wires.
This is the red wire going to the switch, the blue to the circuit breaker and the yellow/green striped wire going directly to ground. Next, strip the ends of the wires about 7mm and then insert them into the terminal block or connector on the wall. Finish by screwing them in.
In the case of a wall light with a DCL box , start by unclipping the terminal block from the box. Then, you must open it by pushing on the lugs. You will then find the terminal block connectors.
Run the electrical wires through the plastic part and connect them. Finally, clip the two parts back together. Once the wall light is connected, secure the wall light and install a bulb and your pendant light.
Wall sconce ideas to make
Do you want to integrate unique models into your lighting system? Know that you will find many decorative tutorials to make Ikea-style wall lights . The possibilities are endless to know how to make a wall light.
For example, you can create a wall sconce with wooden dowels. In this case, you will need 3/4'' 9 square wooden dowels. In addition to these, you will need a decorative metal sheet and a cord lamp kit.
Moreover, by featuring wood in your home, you will achieve elegance and originality. To make a wooden wall light , you can use wooden slats.
These allow you to build a box-style cover to accent a wall sconce. Additionally, you can also design wall sconce lampshades with cardboard postal tubes .
Tips for Making an Industrial Wall Light
To make an industrial wall light , you will first need a support. The support is made with a pine board cut to the desired length and 4 wooden cleats .
The cleats should match the edges of the pine board. Assemble each piece to make a support and attach it to the wall.
The next steps are to:
- Make the sockets and elbows by assembling the parts using super glue,
- Treat the support by varnishing the whole thing,
- Drill the bracket at the desired location for the lamps,
- Attach the clamps to the support,
- Wire the sockets,
- Fix the wall light to the wall,
- Screw in the bulbs.
There are many other DIY decorations to make unique and unusual wall lights. However, you must have a good knowledge of safety standards to install a functional and compliant light fixture.
Leave a comment